川消_萃联
气体灭火系统
自动喷水灭火系统

联系我们

  • 萃联(山东)消防设备有限责任公司
  • 电话:15508683119
  • 地址:山东省济南市历城区祝舜路44号
当前位置:首页 > 新闻中心消防箱栓接头有以下几种安装方式

消防箱栓接头有以下几种安装方式

来源:http://www.cx-fire.com/ 日期:2024-03-29

1、明装采用6×M10镀锌膨胀螺栓固定,螺栓应均匀分布

1. The exposed installation is fixed with 6 × M10 galvanized expansion bolts, and the bolts should be evenly distributed

2、暗装消火栓箱应采用水泥砂浆四周嵌密实,严禁使用混合砂浆填补。

2. Concealed fire hydrant boxes should be tightly embedded with cement mortar around them, and it is strictly prohibited to use mixed mortar to fill them.

3、消防箱在安装过程中,应对消防箱内进行加固措施,以防变形。

3. During the installation process of the fire box, reinforcement measures should be taken to prevent deformation.

4、箱内管道和消火栓安装时,在连接中应保护、防止箱内的油漆脱落。

4. When installing pipelines and fire hydrants inside the box, protection should be provided during the connection to prevent paint from falling off inside the box.

5、按立管位置预留进箱孔,严禁将其它未用敲落孔敲落,箱内的管道应横平竖直。

5. Reserve entry holes according to the position of the riser, and it is strictly prohibited to knock off other unused holes. The pipes inside the box should be horizontal and vertical.

6、消防箱安装完成时,应及时将敞开的箱门采用三夹板封闭;消火栓手柄阀门关紧后及时卸掉保存。

6. When the installation of the fire box is completed, the open box door should be promptly closed with three plywood; Remove and store the handle valve of the fire hydrant in a timely manner after it is tightly closed.

20230531014425408.png

7、成品保护:安装完成后及时处理表面污染并加以保护

7. Finished product protection: After installation, promptly handle surface pollution and provide protection

8、特殊部位安装要求,为了确保装修效果,走廊处的消防箱安装必须与装修紧密配合。

8. The installation requirements for special parts require that in order to ensure the decoration effect, the installation of fire boxes in the corridor must be closely coordinated with the decoration.

通常情况下,室外消火栓常见的地上栓是有三个接口的,两个65MM口径,一个100MM口径,65MM口径对应的是水带的接口,通常为卡口,100MM口径对应的是消防车吸水管,通常为螺纹的,不同的消防栓应使用相应的消防栓接头规格,以上就是本文的全部内容。

In general, the most common outdoor fire hydrant above ground has three interfaces, two 65mm diameters and one 100mm diameter. The 65mm diameter corresponds to the interface of the water hose, usually a bayonet, and the 100mm diameter corresponds to the suction pipe of the fire truck, usually threaded. Different fire hydrants should use the corresponding specifications of the fire hydrant joint. The above is the entire content of this article.


上一篇:湿式自动喷水灭火系统和干式自动喷水灭火系统的区别
下一篇:消防水箱的设置要求

相关产品 / Related products