消防器材在我们的生活中是非常常见的，为我们的生活提供了保障。但是大家对消防器材的分类可能不是很了解，今天就由电控消防水炮厂家为大家讲一下电控消防水炮的详细内容，以及保养的相关事项，希望对大家能有所帮助。

Fire fighting equipment is very common in our life, which provides a guarantee for our life. But you may not know much about the classification of fire-fighting equipment. Today, the manufacturer of electric control fire water monitor will tell you the details of electric control fire water monitor and related maintenance matters, hoping to help you.

一、电控消防水炮使用

1、 Use of electric fire water monitor

1、根据火场的实际情况及火灾的性质，选择使用水炮的直流或喷雾功能。

1. According to the actual situation of the fire and the nature of the fire, choose to use the DC or spray function of the water cannon.

2、向上键是操作炮头向上运动，向下键是操作炮头向下运动，向左键是操作炮体向左运动，向右键是操作炮体向右运动，启动键是开启水炮进水电动阀门，停止键是关闭水炮进水电动阀门。

2. The up key is to operate the gun head to move up, the down key is to operate the gun head to move down, the left key is to operate the gun body to move left, the right key is to operate the gun body to move right, the start key is to open the water cannon water inlet electric valve, and the stop key is to close the water cannon water inlet electric valve.

遥控器为一控四，下方有四个选择键分别对应四台消防炮，当现场发生火情时，打开相应消防炮进行灭火，调整炮头对准着火源然后开启水炮进水阀门，观察落水点保证覆盖着火点，如不行则需要调整到合适位置，灭火结束后，关闭进水电动阀门。

The remote control is one control four, and there are four selection keys under it, which correspond to four fire monitors respectively. When a fire occurs on site, open the corresponding fire monitor to extinguish the fire, adjust the gun head to aim at the fire source, and then open the water inlet valve of the water monitor, observe the water falling point to ensure that the fire point is covered. If not, it needs to be adjusted to the appropriate position. After the fire is extinguished, close the water inlet electric valve.

3、消防炮使用完后应用清水冲洗，向注油孔内注油，并检查各转动部位是否灵活正常，将炮头调整向下，然后排空炮塔水管余水。

3. After using the fire monitor, wash it with clean water, fill the oil hole with oil, check whether the rotating parts are flexible and normal, adjust the gun head downward, and then drain the residual water of the turret water pipe.

二、川消电控消防水炮维护

2、 Maintenance of Chuanxiao electric fire monitor

1、电动防爆消防炮在使用前应先检查控制器电源电路和无线摇控接收设备,保证电流电压在正常范围内.摇控器内电池电量正常。

1. Before using the electric explosion-proof fire monitor, check the power circuit of the controller and the wireless remote control receiving equipment to ensure that the current and voltage are within the normal range The battery power in the remote controller is normal.

2、保持消防炮体清洁，使用泡沫灭火后应用清水冲洗干净。

2. Keep the fire monitor clean, and wash it with clean water after extinguishing with foam.

3、定期在黄油嘴处及转动部位加注润滑脂，保证转动灵活。

3. Regularly fill grease at the grease fitting and rotating parts to ensure flexible rotation.

4、若发现喷射压力过高或射程较近时，应检查喷头处是否有赌塞物，若有应及时。

4. If the injection pressure is found to be too high or the range is close, check whether there is any blockage at the nozzle, and if so, remove it in time.

5、在安装消防炮前，要对管路进行冲洗，以防杂物进入消防炮堵塞喷头。

5. Before installing the fire monitor, flush the pipeline to prevent sundries from entering the fire monitor and blocking the nozzle.

6、各部件应保持完好，如果发现紧固件松动，应及时修复。

6. All parts should be kept in good condition. If fasteners are found to be loose, they should be repaired in time.

以上就是今天为大家介绍的关于问题以及注意事项的全部内容，希望对大家能有所帮助，想要了解更多内容可以电话联系我们或者关注我们的网站http://www.cx-fire.com，我们的工作人员会及时与您取得联系。

The above is all about the problems and precautions introduced to you today. I hope it can help you. If you want to know more, you can contact us by phone or follow our website http://www.cx-fire.com , our staff will contact you in time.