消防压力开关的接线，需要注意的细节是比较多的，不可会出问题。而消防压力开关怎样接线，现在我们一起来看看吧。

There are many details to be paid attention to in the wiring of the fire pressure switch, so there should be no problems. Now let's have a look at how to connect the fire pressure switch.

川消消防压力开关怎样接线

How to connect Chuanxiao fire pressure switch

1、先使用万用表，将消防压力开关的常开点给测量出来，然后接入到模块中的X1和X2常开端子上。注意，消防开关是有4个线的，其中两根常开点和两根常闭点。

1. First use a multimeter to measure the normally open point of the fire pressure switch, and then connect it to the X1 and X2 normally open terminals in the module. Note that the fire switch has four wires, including two normally open points and two normally closed points.

2、要是模块选型不对的话，只需将压力开关使用输入模式便可以了。这里的区别是，输入模块是可以不用DC24V电压的，也不存在外控的输出端子。

2. If the module selection is wrong, just use the input mode of the pressure switch. The difference here is that the input module can not use DC24V voltage, and there is no external control output terminal.

3、压力开关是属于整个消防设备中的主要配件，是需要将其安装于喷淋系统的报警阀上。

3. The pressure switch is the main accessory of the whole fire-fighting equipment, which needs to be installed on the alarm valve of the sprinkler system.

川消消防开关使用需注意什么

What should be paid attention to in the use of Chuanxiao fire switch

1、消防压力开关的重要性是比较大的，当喷淋管道中的压力是比较供水的压力更小的话，则压力开关会启动，同时将产生的动作信号传送到报警系统中，这样控制设备在接收到信息之后，便会进行加压工作。

1. The importance of the fire-fighting pressure switch is relatively large. When the pressure in the spray pipe is smaller than that of the water supply, the pressure switch will start and transmit the generated action signal to the alarm system, so that the control equipment will pressurize after receiving the information.

2、消防系统中的输入模块，也被叫做是监视模块，是用于检查设备是否能够正常工作。只要常开信号设备出现动作，被监视到后，常开端便会出现

2. The input module in the fire protection system, also known as the monitoring module, is used to check whether the equipment can work normally. As long as the normally open signal equipment acts and is monitored, the normally open signal will appear

3、当报警阀在出现动作之后，报警管路是会通水的，而管内的压力在超过了设定好的数值之后，开关便会出现启动，并往系统传达报警阀工作。

3. When the alarm valve acts, the alarm pipeline will be filled with water, and after the pressure in the pipe exceeds the set value, the switch will start and convey the work of the alarm valve to the system.

4、为了预防工作人员的误操作，导致阀门出现关闭的情况，造成系统无法工作。就会在阀门上安装信号的反馈设备，防止出现误操作。

4. In order to prevent the valve from closing due to the misoperation of the staff, resulting in the system unable to work. Signal feedback equipment will be installed on the valve to prevent misoperation.

消防压力开关怎样接线，以及消防开关使用需注意什么的问题就先介绍到这里了，各位是否了解了呢。消防压力开关的接线是不可出错的，否则会影响到后期正常使用。您有什么问题就来我们网站http://www.cx-fire.com咨询吧。

How to connect the fire pressure switch and what should be paid attention to in the use of the fire switch are introduced here first. Have you understood it. The wiring of the fire pressure switch must not be wrong, otherwise it will affect the later normal use. Come to our website if you have any questions http://www.cx-fire.com Consult.