随着消防水炮的普及，故障也时有听说，那么常见的消防水炮故障是什么呢？如何这个故障问题？下面就跟着川消小编一起来分析一番吧。

With the popularity of fire water monitors, failures have been heard from time to time. What are the common failures of fire water monitors? How to solve this problem? Now let's follow Chuan Xiaobian to analyze it.

消防水炮常见故障的一种情况：从水炮口喷出的水既不是柱形也不是雾状。

A common fault condition of fire water monitor: the water sprayed from the nozzle is neither columnar nor foggy.

当出现这种情况时，一般都会认为是水炮的产品质量有问题，可事实却不是，这是因为在安装消防水炮继电器设备时，没有安装过滤网，才导致消防管道内被残渣堵塞，从而出现以上情况。处理方法是改装过滤网，清理管道中的残渣。如果残渣被堵塞在系统的镇流器中时，也会出现以上情况。此时，须找到制造商的技术人员进行。

When this happens, it is generally believed that the product quality of the water monitor is defective, but the fact is not. This is because when the relay equipment of the fire monitor is installed, the filter screen is not installed, which leads to the blockage of the fire pipe by residues, thus the above situation occurs. The treatment method is to refit the filter screen and clean the residue in the pipeline. If the residue is blocked in the ballast of the system, the above situation will also occur. At this time, the manufacturer's technicians must be found to solve the problem.

消防水炮常见故障二种情况：当系统工作时，离心水泵启动后，管道内的工作压力却达不到。

There are two common failures of the fire water monitor: when the system is working, the working pressure in the pipeline cannot be reached after the centrifugal pump is started.

因为消防水炮要实现有效射程，其管道中的工作压力须达到额定压力值。如果工作压力太低，就会出现喷射距离短，无法达到额定射程。因此，这种情况通常是由于管道中气体过多或吸湿水泵底阀无法正常打开造成的，处理方法是对这两部分进行排查。

Because in order to achieve an effective range, the working pressure in the pipeline of the fire monitor must reach the rated pressure value. If the working pressure is too low, the injection distance will be short and the rated range will not be reached. Therefore, this situation is usually caused by too much gas in the pipeline or the bottom valve of the moisture absorption pump cannot be opened normally. The treatment method is to check these two parts.

常见的消防水炮故障三种情况：消防控制室不能远程启动离心泵。一般来说，这种情况可以行路线排查维修，如果真的出现引路或短路故障，当然会出现无论怎么操作，离心泵系统都不会启动。还有一种情况是联动操控琴台按钮出现故障也会导致上述情况发生。处理方法是对主机按钮或实际操作盘进行维修。

There are three common cases of fire water monitor failure: the fire control room cannot remotely start the centrifugal pump. Generally speaking, in this case, the route can be checked and repaired first. If there is a lead or short circuit fault, of course, no matter how you operate, the centrifugal pump system will not start. Another case is that the failure of the linkage console button will also lead to the above situation. The handling method is to repair the host button or the actual operation panel.

消防水炮常见故障的三种情况就讲解到这里了，您对此有什么疑惑随时来我们网站http://www.cx-fire.com进行咨询吧！

Here are three common failures of the fire water monitor. If you have any questions, please come to our website at any time http://www.cx-fire.com Consult!