高压细水雾分区控制阀关键功能是接收消防报警系统控制板的操作数据信号，打开相对系统分区的电动截止阀，将细水雾释放到保护区进行灭火。那么高压细水雾灭火系统应用分区控制阀的性能特点是什么呢？

The key function of the high-pressure water mist partition control valve is to receive the operation data signal from the control panel of the fire alarm system, open the electric stop valve relative to the system partition, and release the water mist to the protection area for fire extinguishing. So what are the performance characteristics of partition control valve in high-pressure water mist fire extinguishing system?

多种启动方式，电动、机械应急启动。采用电动球阀驱动矩形，启动快。工作压力范围宽，可达16MPa。具有多种流量和压力的高压泵。高压泵的主要部件由不锈钢制成。按照系统真实情况，可以通过泵组合实现多种流量和压力输出。

Various startup modes, electric and mechanical emergency startup. The electric ball valve is used to drive the rectangle, which is fast to start. The working pressure range is wide, up to 16MPa. High pressure pump with multiple flows and pressures. The main components of the high-pressure pump are made of stainless steel. According to the real situation of the system, a variety of flow and pressure outputs can be realized through the combination of pumps.

根据不同的应用方法，开式系统分区调压阀有两种应用方法:开式系统软件-由开式系统分区调压阀+开式喷嘴组成。预作用系统软件-由开式系统分区调压阀+闭式喷嘴组成。

According to different application methods, there are two application methods of open system partition pressure regulating valve: open system software - composed of open system partition pressure regulating valve + open nozzle. Pre action system software - consists of open system partition pressure regulating valve + closed nozzle.

高压细水雾分区控制阀由电动截止阀、手动球阀、压力控制器、气压计、外壳和连接管组成；其主要功能是接收火灾报警控制器的控制信号，打开相应分区的电动截止阀，向保护区释放细水雾。当喷嘴正常喷出细水雾时，压力开关将反馈给火警控制器。

High pressure water mist zone control valve is composed of electric stop valve, manual ball valve, pressure controller, barometer, shell and connecting pipe; Its main function is to receive the control signal from the fire alarm controller, open the electric stop valve in the corresponding zone and release water mist to the protection area. When the nozzle sprays water mist normally, the pressure switch will feed back to the fire alarm controller.

分区控制阀配有紧固件螺母和焊管。用氩弧焊与焊管焊接后，用活接头与阀组的进出口连接。分区控制阀组安装在保护区附近和保护区外，以方便发生火灾时的紧急情况。分区控制阀组采用明装和暗装两种方式安装。山东川消人员提醒大家在进行暗装时，装修前要检查接缝是否密封好。

The zone control valve is equipped with fasteners, nuts and welded pipes. After welding with the welded pipe by argon arc welding, use the union to connect with the inlet and outlet of the valve group. The divisional control valve group is installed near and outside the protection area to facilitate the emergency in case of fire. The divisional control valve group is installed in two ways: open installation and concealed installation. Shandong Chuanxiao staff reminded everyone to check whether the joints are well sealed before decoration.

高压细水雾灭火系统应用分区控制阀的性能特点内容便讲解完毕了，如果您对消防设备感兴趣或者有需求的话可以来川消网站www.cx-fire.com咨询了解，为您提供很好的相关设备。

The performance characteristics of zone control valve used in high-pressure water mist fire extinguishing system are explained. If you are interested in or need fire-fighting equipment, you can come to Chuanxiao website www.cx-fire.com Com to provide you with good relevant equipment.